HPTuners VCM Suite
HPTuner's VCM Suite will allow you to tune your OBD2 equipped vehicle, given that it is on the list of supported vehicles. If you are not familiar with their setup, please check their site at http://www.hptuners.com/
There are 2 versions of the suite, Regular, and Pro. With the Pro …
$499.99
Innovate LC-1 Standalone Wideband Controller
The LC-1 includes the sensor, cable, deep bung with plug, wiring for ground/calibration and logworks software to record through a serial port.
You can check out the installation directions here.
The LC-1 Lambda cable is a complete wideband controller built in to a sealed cable. It features …
$179.99
ARP Header Studs
Headers can represent a sizable investment, so you'll want to keep them securely attached. In addition, exhaust leaks can cost you power and even cause damage to your vehicle. ARP has the answer, in the form of their stainless steel header studs. They're made from premium 300 stainless steel…
$109.99
Manley Steel Retainers and Keepers
Set of 12 Manley LS retainers and keepers, made in the USA. 13% lighter than stock per valve and more consistant install height than Comp. Manley shaved the top of the retainer to be flush with the keepers, which gives more clearance between the retainer and the rocker arm. Titanium…
$89.99
Comp 26915 Valve Springs
Set of 12 Comp 26915 Valve Springs
105 @ 1.800"
293 @ 1.200"
Coil Bind @ 1.100
313 lb/in spring rate
…
$149.99
Comp Cams 26986 Valve Springs
Set of 12 Comp 26986 Valve Springs
123 @ 1.750"
284 @ 1.175"
Coil Bind @ 1.060
280 lb/in spring rate
…
$164.99
Custom Length Pushrods
Custom length pushrods are the correct length for our performance cams, and stiffer than the stock pushrod. While some have ran stock pushrods on reground and Comp camshafts, the proper preload on the hydraulic lifter is important for the best performance from the cam. The 60V6 is fortunat…
$139.99
Performance Rod Bearings for Forged Rods
These Clevite H series bearings are meant for the Forged I and H beam connecting rods offered here on WOT-Tech. 60V6 bearing tangs will not line up properly with the SBC tangs used.
Clevite H-Series rod bearings were primarily developed for NASCAR racing, but are well su…
$59.99
Performance Rod Bearings for 60V6 rods
These Clevite H-Series rod bearings are a drop in performance upgrade for stock 5.7" forged connecting rods found in the 2.8-3400 engines,
Clevite H-Series rod bearings were primarily developed for NASCAR racing, but are well suited to other types of competition engines. They're es…
$119.99
Locking Header Bolts
Sold in sets of 12. Torque to 20ft lbs MAX. Max locking pin Torque is 60 INCH lbs.
Our Bolts Don't Back Out!
The Split Lock TM Friction Lock Fastener design uses a locking set pin built in to the bolt, When tightened the set pin expands the bolt threads against the thread wa…
$60.99
ARP 3500 Connecting Rod Bolts
The rod bolts are put under amazing amounts of stress under a heavy engine loads. These are a must for the serious engine builder. Made from 8740 Chromoly steel, with rolled threads for superior stud to block clamping pressure. These studs have a tensile strength of 220,000 PSI.
For all 3500 3900 a…
$89.99
Main Stud Kit
Strengthen your bottom end with this high quality parts from ARP. Kit includes washers, studs, nuts, and ARP moly lube (not pictured). Long enough for use with a windage tray. Windage Tray holes will need to be opened up to fit the stud. You will need to have your mains line …
Your basket is empty.
 (WinCE).jpg "HPTuners VCM Suite")
.JPG "Innovate LC-1 Standalone Wideband Controller")
 (WinCE).jpg "ARP Header Studs")
 (WinCE).jpg "Manley Steel Retainers and Keepers")
 (WinCE).jpg "Comp 26915 Valve Springs")
 (WinCE).jpg "Custom Length Pushrods")
.jpg "Locking Header Bolts")
.jpg "ARP 3500 Connecting Rod Bolts")
